Curt Class IITrailer Hitch Installation - 2012 Chrysler 300- Video

Hi there, Chrysler owners. Today on your 2012 Chrysler 300, we're gonna be taking a look at and showing you how to install Draw-Tite's 1 1/4 inch trailer hitch receiver. And this is what our hitch looks like when it's installed. The cross tube is gonna be visible underneath the vehicle, as well as the receiver here at the back. It does tuck up pretty far, so as long as you're standing up, you really don't notice it too much, but it is noticeable once you get up on the vehicle here. It's a class II, 1 1/4 by 1 1/4 receiver. more

Watch Video

8/16/2021 3:07:13 PM

Draw-Tite Max-Frame Trailer Hitch Installation - 2018 Chrysler 300- Video

Hey everybody, Ryan here at etrailer. Today on our 2018 Chrysler 300, we're gonna be showing you how to install the Draw-Tite Max-Frame Trailer Hitch Receiver. But before we do that, why don't we check out the hitch and make sure that it's something that's gonna work for you. So me personally, if I was looking for a hitch for my 300, I'd want something that will look decent. These are good looking cars, and I really want a giant hitch hanging below the vehicle. And honestly, I think this one looks pretty good. more

Watch Video

5/20/2021 8:28:20 AM

Draw-Tite Max-Frame Trailer Hitch Installation - 2013 Chrysler 300- Video

Today on our 2013 Chrysler 300, you're going to be taking a look at, I'm going to show you how to install a Draw-Tite class III max-frame trailer hitch receiver, part number 76145. This is what our hitch looks like when it's installed. As you can see, the cross tube is visible. However, it's nice and tucked up close to the bottom of our vehicle, so it doesn't take away from the look.Our receiver tube is also tucked in nice behind the outer edge of our bumper fascia, so we're not going to have to worry about hitting our legs or shins on it when we're unloading and loading the vehicle. It's going to be a class III hitch. It's going to have a 2" x 2" receiver tube opening. more

Watch Video

1/15/2019 4:12:52 PM

Trailer Hitch Installation - 2013 Chrysler 300 - Curt- Video

Today on our 2013 Chrysler 300, we'll be installing the Curt Class III two inch receiver trailer hitch. Part number C13093. You can see a very minimal amount of the hitch hangs down. The two inch receiver is very easy to get to. It's not up underneath the bumper too far, so you can easily slide your draw bar, your bike rack or your cargo carrier in there. Our five eighths hitch pin hole here is easily accessible. You don't have to worry about it getting in the way of this plate here or where the safety chain loops are right here, to attach the safety chains on your trailer. more

Watch Video

6/14/2016 10:56:06 AM

Trailer Hitch Installation - 2013 Chrysler 300 - Curt C12064- Video

Today on our 2013 Chrysler 300, we will be installing the Curt Class II 1-1/4" Receiver Hitch, Part Number C12064. As you can see, a very minimal amount hangs down. The only part you really see is the 1-1/4" receiver right here and the two loops that are easily accessible for our safety chain hooks for our trailer to attach to. It has a nice gloss black powder-coated finish, so it'll be durable and provide us some corrosion residence from the salt and road grim and debris which may come in contact with it. This hitch has a 3,500-pound gross trailer weight reading and a 350-pound max tongue weight rating. You'll want to consult the owner's manual of your Chrysler 300 and go by the numbers that are listed in it. For a few measurements to better assist you in choosing any hitch-mounted accessories such as ball mounts, bike racks, or cargo carriers, you're looking at about 8 1/4" from the ground to the top of the 1 1/4" receiver, and you're looking at about 6" from the center of the 1/2" diameter hitch pin hole out to the far point of the bumper. If you're using this for a non-trailer application, such as using it for a bike rack or a cargo carrier, Curt requires that you use a cargo stabilization strap just to help support some of the load that is being placed on the hitch. more

Watch Video

6/10/2016 10:21:17 AM

Trailer Hitch Installation - 2013 Chrysler 300 - Draw-Tite- Video

Today on our 2013 Chrysler 300, we'll be installing the Draw-Tite Class 2 inch and a quarter trailer hitch receiver, part number 36548. Here's what our Draw-Tite hitch looks like installed. As you can see, it's a really clean installation. A very minimal amount is hanging down beneath the vehicle, just the inch and a quarter receiver right here sticking out a little bit underneath the bottom lip of the bumper, but it's still recessed behind the actual edge of the bumper, so it's not something you're going to be walking by and hitting your shin or your knee on. Plate here on the bottom of the hitch gives us a nice, secure mounting location for our safety chains, really easy to get to for you. This hitch has a half-inch diameter pin hole here, so you're going to use that for your hitch pin, your locking device, to secure your ball mount, bike carrier, or cargo rack. Just keep that in mind. This hitch has a 3500-pound max gross trailer weight rating, and a 300-pound max gross tongue weight rating. Now you want to consult the owner's manual of your Chrysler 300 and go by its number listed there. If the vehicle's only rated to tow 3000 pounds, obviously you don't want to go to the 3500 pounds that the hitch is rated for, or you could cause damage to the vehicle. Now for a few measurements to help you in choosing any hitch mounted accessories out there for you, such as ball mounts, bike racks, or cargo carriers, you're looking about six inches from the center of the hitch pin hole, out to the back of the bumper cover, and you're looking about ten inches from the ground to the top of the inch and a quarter Class 2 opening on the hitch. more

Watch Video

6/7/2016 2:16:23 PM

Trailer Hitch Installation - 2012 Chrysler 300 - Hidden Hitch- Video

Today on our 2012 Chrysler 300 we're going to be taking a look at, then showing you how to install, the Hidden Hitch Custom Fit Class II Trailer Hitch Receiver with the 1-1/4" by 1-1/4" opening. Part number is 90243. Here's what our hitch looks like installed, as you can see, if you get down low, you'll see that cross tube a little bit, but just kind of normal standing around, it's going to remain a little bit hidden for us, which is nice. The main part you'll see are going to be our safety chain connection plate here and our 1-1/4" receiver tube opening. See that does have the reinforced strap around the end to give us a little extra support there. The plates are also going to do a good job of stiffening that up for us. You can see the safety chain connection points are here. more

Watch Video

4/7/2016 3:46:22 PM

Trailer Hitch Installation - 2012 Chrysler 300 - Draw-Tite- Video

Today on our 2012 Chrysler 300, we're going to take a look at and show you how to install the Draw-Tite Custom Fit Class II Trailer Hitch receiver with the 1-1/4-inch by 1-1/4-inch opening. Part number is 36548. Here's what our hitch looks like installed. As you can see, if you get down low, you'll see that cross tube a little, but just normal standing around, it's going to remain a little bit hidden us for, which is nice. The main part you'll see is going to be our safety chain connection plate here and our 1-1/4-inch receiver tube opening. See that does have the reinforced strap around the end to give us a little extra support there. The plates are also going to do a good job of stiffening that up for us. You can see the safety chain connection points are here. more

Watch Video

4/7/2016 3:45:44 PM

Trailer Hitch Installation - 2010 Chrysler 300 - Curt- Video

Today on our 2010 Chrysler 300, we're going to take a look at then show you how to install the Curt custom fit class three trailer hitch receiver. This offers a two inch opening. It's part number is one three four six five. Here's what the hitch is going to look like once you get it installed on your vehicle. As we can see, it's a nice, clean looking hitch. It's a class three, so we're going to have a lot of great uses for this whether we want to do our bike racks, some towing options this is going to offer all the way up to a three hundred fifty pound max tongue weight capacity, a thirty five hundred pound gross trailer weight capacity. more

Watch Video

5/14/2015 4:56:42 PM

Trailer Hitch Installation - 2015 Chrysler 300 - Curt- Video

Today on our 2015 Chrysler 300 we'll be installing the Curt 2" Receiver Tube Hitch, part number C13093. We've already got our hitch installed so we can see what it looks like. Here, we've got a nice rectangular or square tube cross tube that helps keep it nice and tight to the bottom of the vehicle while we still have access to our chain hold downs and our receiver tube. In the receiver tube it's already been pre-drilled for the 5/8ths standard pin and clip. This is a Class III hitch so it has a 350 lb tongue weight capacity and a 3500 lb tow capacity. I'll give you a couple measurements that will assist you with selecting accessories for your new hitch. more

Watch Video

1/30/2015 12:37:39 PM

Trailer Hitch Installation - 2009 Chrysler 300 - Curt- Video

Today, on our 2009 Chrysler 300, we'll be installing the Curt Hitch, part number C12240. Here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch, such as a ball mount, bicycle rack, or cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is approximately 6-3/4 inches. From the top of the opening in the receiver to the ground is approximately 10 inches. Now let's go ahead and install our hitch. To begin with, we'll need to go ahead and lower our exhaust out of the way. more

Watch Video

10/27/2014 2:42:49 PM

Trailer Hitch Installation - 2007 Chrysler 300 - Curt- Video

Today on our 2007 Chrysler 300, we will be installing Curt Hitch, part number C12240. Before we begin our installation, here are a few measurements to help you on selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch pin hole to the outer most part of the bumper is 7 inches. From the top of the receiver tube to the ground is 12 inches. Now lets go ahead with our install. Before we begin our installation, we will need to lower our exhaust. Well first put a safety strap underneath the vehicle to hold the exhaust while we undo the mounting location. On the two rear most isolators, we can go ahead and undo the bolts holding the isolators to the vehicle. more

Watch Video

3/7/2013 3:23:59 AM

Trailer Hitch Installation - 2005 Chrysler 300 - Curt- Video

Today on our 2005 Chrysler 300, we'll be installing the CURT hitch, part number 13465. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch-pin hole to the outermost edge of the bumper is 6 3/4 inches. From the top of the receiver tube opening to the ground will be 10 1/4 inches. This will assist you selecting accessories, such as a drawbar, a bike rack, or cargo carrier. more

Watch Video

2/15/2013 2:18:29 PM

Trailer Hitch Installation - 2006 Chrysler 300 - Curt- Video

Today on our 2006 Chrysler 300, well be installing the Curt Hitch, part number 13465. This is what our hitch will look like once it's installed. Next, well give you a couple of measurements to assist you with selecting accessories for your new hitch. In the center of the hitch pinhole to the outermost edge of the bumper, is seven inches. From the top of the receiver tube, to the ground is 10 inches. This will assist you with selecting accessories, such a drawbar, a bike rack or cargo carrier. more

Watch Video

6/4/2012 1:46:12 PM

Trailer Hitch Installation - 2007 Chrysler 300- Video

Today on this 2007 Chrysler 300 we are going to be installing Curt hitch part number 13465. We are underneath the vehicle, the first thing we want to do is lower down the exhaust. Depending on your model you may have a single exhaust or a dual exhaust. On this particular vehicle we have a single exhaust. There is a hanger here at the rear side of the exhaust and a second one here at the forward side that we want to remove as well. If we follow forward we need to lower down these two hangers here as well. On the rear hanger some models will have this grounding strap, you want to make sure you take that off as well before you lower the exhaust down. :39 more

Watch Video

7/23/2010 12:18:26 PM

  1